Miscellaneous Grips/Pads/Stocks

The Low Profile M-LOK Rail, driven by an end user request for a solution to mount an aiming laser as close to a M-LOK handguard as possible. Getting the aiming laser closer to the bore axis reduces offset and also reduces snag hazard of the laser on the...

The Advanced Technology Int. Shotforce Top-Folding Shotgun Stock is a 12ga and 20ga (proud fit) Stock. It fits Maverick 88 12ga & 20ga (proud fit), Mossberg 500/535/590/835 12ga & 20ga (proud fit), Remington 870 12ga & 20ga (proud fit), American Tactical...

The Midwest Industries Ultra Lightweight One-Piece Free Float MP5K Handguard is constructed of rugged 6061 aluminum with a hard coat anodized finish. It features a Tri-Rail 1913 Picatinny on 3 sides for accessory attachment, M-LOK angled slots for light...

The TacStar Shotgun Grips were designed with the proper width, rearward angle and back swell to distribute recoil energy evenly into both hands resulting in greater speed, accuracy and control when shooting. Injection-molded from a high-impact ABS...

The TacStar Shotgun Grips were designed with the proper width, rearward angle and back swell to distribute recoil energy evenly into both hands resulting in greater speed, accuracy and control when shooting. Injection-molded from a high-impact ABS...

The Sticky Stock Pad/Riser is a significant improvement over other products on the market. The base and cheek pad/riser are made from their padded Sticky Material to ensure the SPR does not slip or move especially at the moment the trigger is squeezed...

The Spikes Tactical Delta Ring assembly is fully Mil-Spec and comes ready for you to finish your new upper. The barrel nut is machined from tough chromoly steel, is properly heat treated, and of course completed with a phosphate finish. The weld spring...

The Spikes Tactical M4 Complete Stock Assembly comes with everything you need to finish off the back end of your AR-15 lower receiver with top notch parts. This kit comes with a 6 position Mil-Spec Buffer Tube, M4 Collapsible Buttstock, Receiver End...

Strike Industries LINK attachment system takes the age old question Key-Mod vs. M-LOK and came up with the ultimate solution, a dual interface design compatible with both M-LOK and Key-Mod, same hardware with no need for additional parts. This Aluminum...

Strike Industries Ar Carbine Flat Wire Spring Si-ar-fws-cFit: AR RiflesDescription: Advanced Receiver Extension

Built for durability, reliability, and undeniable style, the all new X65 Sharktooth for the Sig P365X is the perfect addition to your daily carry! This custom, in-house designed frame is custom stippled with a hybrid design for superior grip and feel...

The RS Regulate M-LOK Rail made for the Galil ACE pistol length gas system with twin opposed handguard bolts will allow the end user to customize this iconic firearm platform. This Rail IS NOT COMPATIBLE with pistol style or rifle length with single long...

The RS Regulate M-LOK Rail made for the Galil ACE rifle length gas system rifles with twin opposed handguard bolts will allow the end user to customize this iconic firearm platform. This Rail IS NOT COMPATIBLE with pistol style or rifle length with...

The BM-s Accessory Mount allows the end user to be able to mount their preferred forward accessories to their AKM spec barrel. With a .59" Diameter, this accessory mount will allow the use of any attachment that accepts picatinny style mounting. Weighing...

Primos Hunting Trigger Stick Onyx, Yoke, Matte Black/smoke Gray 65823Model: Trigger Stick Onyx

Pachmayr Gripper Grips are made from a specially formulated rubber compound which optimizes control and recoil absorption. The finger groove style is popular for combat shooting and hunting. A covered backstrap and slight palm swell fills the hand but is...

Pachmayr Signature Grips feature a unique full wrap-around design and are made from rubber specially formulated for use on semi-automatic pistols. This rubber compound gives them a feel that is unmistakably Pachmayr. Built-in steel inserts ensure they...

Pachmayr is proud to introduce the Diamond Pro Series revolver grips. This grip line is designed to fill the hand comfortably, with natural feel and point. The unique shape is covered with their Diamond Plate texture. This gives you rugged good looks and...

Pachmayr is proud to introduce the Diamond Pro Series revolver grips. This grip line is designed to fill the hand comfortably, with natural feel and point. The unique shape is covered with their Diamond Plate texture. This gives you rugged good looks and...

This Buttstock Cheek Rest Riser with magazine pouch fits most rifles by tightening a laced cinch on its bottom. The integrated magazine pouch is large enough to holds an AR-15 or AK-47 magazine, and mounts to either side of the cheek riser via a hook and...

The NAA Holster Grip is one of the most innovative gun/grip configurations in the firearms industry. Available for both Magnum and Long Rifle frame size mini-revolvers, the rugged plastic sheath (with ambidextrous clip) folds knife-like against the...

The NAA Holster Grip is one of the most innovative gun/grip configurations in the firearms industry. Available for both Magnum and Long Rifle frame size mini-revolvers, the rugged plastic sheath (with ambidextrous clip) folds knife-like against the...

Midwest Industries Side Folder With Light Weight Stock, Black, Fits Picatinny Rail Mi-stap-sf-lwsModel: Side Folder with Light Weight StockFit: Picatinny

Midwest Industries Side Folder With Mi Stock Tube, Black, Fits Picatinny Rail Mi-stap-sfModel: Side Folder with MI Stock TubeFit: Picatinny

Midwest Industries Stock Tube With Light Weight Stock, Black, Fits Picatinny Rail Mi-stap-lwsModel: Stock Tube with Light Weight StockFit: Picatinny

Midwest Industries Stock Tube With Buffer Tube Adaptor, Black, Fits Picatinny Rail Mi-stap-btModel: Stock Tube with Buffer Tube AdapterFit: Picatinny

KRISS USAs Vector Picatinny 7 Slot Side Rail Kit allows you to mount your favorite Picatinny compatible accessories to your KRISS Vector. Attaches to provided hard points on the Vector receiver, or the Mk1" Mk9" and Mk11 Vector handguards. This is...

Precision fit for the Ruger 22/45 MkIVFeatures :Gentle palm swells fit comfortably in handFinger grooves naturally position fingers for optimal gripTextured with Hogues famous Cobblestone pattern for increased comfort and gripMade from long lasting...

Precision fit for the Ruger Mark IVFeatures :Gentle palm swells fit comfortably in handFinger grooves naturally position fingers for optimal gripTextured with Hogues famous Cobblestone pattern for increased comfort and gripMade from long lasting durable...

Precision fit for the Kimber Micro 9Features :Gentle palm swells fit comfortably in handFinger grooves naturally position fingers for optimal gripTextured with Hogues famous Cobblestone pattern for increased comfort and gripMade from long lasting durable...

The Beretta 1301 Tactical Shotgun has become incredibly popular. Along with that popularity comes all types of innovations, and customizations. One of the most sought after is replacing the original factory handguard or forearm with the Magpul Zhukov...

The Beretta 1301 Tactical Shotgun has become incredibly popular. Along with that popularity comes all types of innovations, and customizations. One of the most sought after is replacing the original factory handguard or forearm with the Magpul Zhukov...

GG&Gs SFG-1 Short Vertical Forend Grip has a low profile ergonomic design without sacrificing functionality and is perfect for keeping CQB style weapons as compact as possible. A vertical grip for the AR-15 and M-16 has become a valued tactical accessory...

GG&Gs AR-15 Harris Bipod Adapter is extremely rugged and low profile. Features of the GG&G Bipod Adapter include a stationary standard swivel stud, a counter sunk locking cross bolt that helps eliminate the possibility of snags, a clamping side bar that...

GG&Gs AR-15 Vertical Forend Grip offers a very stable vertical grip and the new waterproof compartment will now accommodate an AR-15/M16 spare bolt. The interior of the ,O, ring sealed waterproof compartment has been re-configured to securely hold the...

Fortis Manufacturing, Inc. Rev Ii,Free Float Handguard, Mlok, Fits Ar-15, Black Rev-ii-12-mlModel: Rev IIFit: Fits AR-15

Fortis Manufacturing, Inc. Night Rail, Free Float Handguard, Keymod, Fits Ar-15, Black Ntr-12-kmModel: Night RailFit: Fits AR-15

The Rapid Adjustment Precision Stock (RAPS) incorporates the mandatory features of a precision stock: integrated cheek rest and adjustable length of pull (LOP), but with the added benefits of easy manipulation, reduced weight and cutting edge features...

The Gradus pistol grip incorporates the results of numerous requests for an ergonomic rubberized grip that will have a relatively straight profile for long range precision shooting and CQB scenarios. It was designed with a 15 degree profile and rigorous...

The Gradus pistol grip incorporates the results of numerous requests for an ergonomic rubberized grip that will have a relatively straight profile for long range precision shooting and CQB scenarios. It was designed with a 15 degree profile and rigorous...

Caldwell Accumax Bipod, Universal, 6"-9" Height, Black Finish 1081953Model: BipodFinish/Color: BlackFit: UniversalSize: 6"-9

Caldwell Bipod, Xla, Mlok/keymod Compatible, 9"-13" Height, Black Finish 1081951Model: BipodFinish/Color: BlackFit: MLOK CompatibleSize: 9"-13

Berettas 92/96 Series Standard Wood Grips with Medallion come in a set of 2 (grip screws not included) and are genuine walnut grips with elegant checkering for Models 96" 92FS" 92A1" M9" M9A1" Brigadier, Centurion and Elite.Features :Fits: 96 - 92FS -...

Berettas 92/96 Series Genuine Walnut Grips have oval checkering with trident and comes in a set of 2. Fits FS Models excluding versions Stock, Combat, Billennium, Compact and Compact Type M (Grip screws not included). Made in Italy.Features :Genuine...

The Battle Arms Development Sabertube is a butt stock that is perfect for keeping your rifle setup as lightweight as possible. Made from 7075-T6 aircraft grade aluminum, this stock is as durable as it is lightweight. This model features a built-in...

This Battle Arms Development 6 Position Carbine Buffer Tube is constructed from 7075-T6 aircraft-grade aluminum has a hard black anodized finish, will fit all standard AR15/M16/M4 lower receivers, and is made in the USA. Battle Arms Development, Inc. (B...

The Adaptive Tactical Tac-Hammer RM4 Stock is the most advanced and versatile stock available for the extremely popular Ruger 10/22 rifle. This innovative stock is loaded with more features than any other on the market. The pistol grip is designed to fit...

The Patent Pending Arisaka Zero Retention Clamp (ZRC) greatly reduces zero shift for lasers and iron sights that are mounted on the handguard of the MCX Virtus and Spear LT. This version is designed for the MCX Virtus chambered in 5.56 and 300BLK" and...

The Patent Pending Arisaka Zero Retention Clamp (ZRC) greatly reduces zero shift for lasers and iron sights that are mounted on the handguard of the MCX Virtus and Spear LT. This version is designed for the MCX Virtus chambered in 5.56 and 300BLK" and...

The Arisaka QD Mount is a low profile design for M-Lok handguards. It features an anti-rotation interface and accepts all standard QD sling swivels, as well as the Geissele/ALG Defense forged QD sling swivel.Features :,Height: 0.375";"Weight: 0.3 oz,

The Apex Optimized Grip for the CZ Scorpion EVO 3 S1 fits both the pistol and carbine and optimized grip angle improves overall ergonomics when compared to the factory grip. It is designed so the trigger assembly can be removed without removing the grip...

The Advanced Technology Int. Shotforce PGS is a 12ga and 20ga (proud fit) shotgun pistol grip stock with an X Series recoil reducing butt-pad. It fits Maverick 88 12ga & 20ga (proud fit), Mossberg 500/535/590/835 12ga & 20ga (proud fit), Remington 870"...

The Advanced Technology Int. Shotgun Mag Clamp or 1" Light Mount and Sling Swivel Stud fits all 12 gauge shotguns. It strengthens the connection of the Mag extension to the barrel and may also be used to mount a 1" diameter light or laser to the barrel...

High quality components and precise manufacturing make Advance Tech parts ideal for maintaining and upgrading firearms. The durability, reliability and excellent build quality of these parts will ensure years of service you can count on.Features...

The Advanced Technology Int. Fiberforce Ruger 10/22 Thumbhole Rifle Stock fits most Ruger 10/22 but will not accommodate rifles equipped with bull barrels. Its Dragunov Military design is lightweight and has a ventilated forearm and handguard. The...

The Advanced Technology Int. Mosin Nagant Monte Carlo Rifle Stock in Black fits most 91/30 Rifles & M-38" M-44 Carbines and Mosin Nagant Variants 7.62x54R. (Will not Fit Firearms with a Hex Receiver, Some Minor Modification may be Required). The X Series...

High quality components and precise manufacturing make Advance Tech parts ideal for maintaining and upgrading firearms. The durability, reliability and excellent build quality of these parts will ensure years of service you can count on.Features...

The Advanced Technology Int. Shotforce Six-Position Adjustable Pistol Grip Stock & Forend Package fits most H&R/NEF 12" 16" & 20 Ga, 410" H&R and NEF single shot shotguns or rifles. Does not fit the H&R Pardner Pump or Compact Model Firearms. It is...

Revolutionize your shooting experience and upgrade the concealed carry potential of a SIG-SAUER P365 XMacro with the Wilson Combat P365 XMacro grip module. Their molded polymer grips will not only improve your grasp on the gun but also control recoil...

Revolutionize your shooting experience and upgrade the concealed carry potential of a SIG-SAUER P365 XMacro with the Wilson Combat P365 XMacro grip module. Their molded polymer grips will not only improve your grasp on the gun but also control recoil...

Revolutionize your shooting experience and upgrade the concealed carry potential of a SIG-SAUER P365 XMacro with the Wilson Combat P365 XMacro grip module. Their molded polymer grips will not only improve your grasp on the gun but also control recoil...

Revolutionize your shooting experience and upgrade the concealed carry potential of a SIG-SAUER P365 XMacro with the Wilson Combat P365 XMacro grip module. Their molded polymer grips will not only improve your grasp on the gun but also control recoil...

Revolutionize your shooting experience and upgrade the concealed carry potential of a SIG-SAUER P365 XMacro with the Wilson Combat P365 XMacro grip module. Their molded polymer grips will not only improve your grasp on the gun but also control recoil...

Revolutionize your shooting experience and upgrade the concealed carry potential of a SIG-SAUER P365 XMacro with the Wilson Combat P365 XMacro grip module. Their molded polymer grips will not only improve your grasp on the gun but also control recoil...

Revolutionize your shooting experience and upgrade the concealed carry potential of a SIG-SAUER P365 XMacro with the Wilson Combat P365 XMacro grip module. Their molded polymer grips will not only improve your grasp on the gun but also control recoil...

Wilson Combat Grip Module, Fits P320, X-compact, No Manual Safety, 320-xcsbFit: WCP320, X-Compact, No Manual SafetyDescription: Grip Module

Wilson Combat Grip Module, Fits Sig P320, Compact, No Manual Safety, Tan 320-ccstFit: Sig P320 Compact with No Manual SafetyDescription: Grip Module

The impressive modular capability of the SIG-SAUER P320 is why it has become a favorite with practical shooters and its thoroughly tested design will be the official US Military sidearm for many years to come. Wilson Combat has now reengineered the P320...

Wilson Combat Grip Module, Fits P320, Carry Ii, No Manual Safety, 320-c2sbFit: WCP320, Carry II, No Manual SafetyDescription: Grip Module

The Super Slim Vertical Foregrip is CNC Machined from Lightweight Aircraft Aluminum with a Durable Matte Black Finish. Includes Red and Blue Anodized Aluminum Inserts for Added PersonalizationFeatures :Dehorned CornersMelted Contours with a Slim...

This foregrip features 6061-T6 Aluminum Construction Finished in a Matte Black Anodization. Lightweight, Ergonomic, and Slim Profile with Machined Grip Serrations.Features :6061-T6 AluminumSlim Profile with Machined Grip Serrations

This foregrip features 6061-T6 Aluminum Construction Finished in a Matte Black Anodization. Lightweight, Ergonomic, and Slim Profile with Machined Grip Serrations.Features :6061-T6 AluminumSlim Profile with Machined Grip Serrations

The UD Arca Dynalock Rail can be installed using the M-LOK fasteners provided or by a qualified gunsmith. By upgrading to the Arca Dynalock Rail, you can enjoy the benefits of both Arca and Dynalock accessories on your firearm. The most popular...

Ultradyne has fine-tuned the design of the Adjustable Butt Stock by offering optional weights for optimal performance in both hunting and competition settings. The Adjustable Butt Stock is already lightweight (just over 1 pound) with the principle that...

From target archery and crossbow hunting to carry pistols and tactical competition, TruGlo has accessories to improve your gear.Features :Increase stability and accuracyGreat for rifles, shotguns, crossbows, airguns, and muzzleloadersRotating head design...

The Presscheck Barricade Stop is a precision-engineered MLOK accessory that achieves two functions in the same footprint, it serves as a Barricade Stop and a QD Sling Mount. The flush mounting and compact design allow the shooter greater ease of movement...

The Presscheck Barricade Stop is a precision-engineered MLOK accessory that achieves two functions in the same footprint, it serves as a Barricade Stop and a QD Sling Mount. The flush mounting and compact design allow the shooter greater ease of movement...

MOD 2 4140 Steel Body Buffers have a unique fluted design with minimum contact points, allowing debris to clear easily, while the FNC LIFE HD treatment chemically bonds in lubrication for smoother cycling. Weight: 4.5 oz. The H2 buffer is a standard...

This AR-15 6 position carbine stock U.S. marked recoil pad adds 1/2" length of pull to AR-15 / M16 carbines equipped with six 6 position collapsible stocks as fitted to the M4 Carbine.Features :The pad features U.S. and ordnance flaming bomb markingsThe...

The Pearce Grip 1911 Pistol Grip Adapter replaces the pistol grip of the AR-15 rifles series with one that accepts most 1911 Government Model grips panels. The grip angle achieved with its application is the same as the popular 1911. Due to clearances on...

The ARCA rail was designed to give you the flexibility and ease of use that you need for mounting your rifle. This rail system is commonly used for mounting Arca Swiss style tri-pods but it also can be used with Arca Swiss style bi-pods too, making...

The ARCA rail was designed to give you the flexibility and ease of use that you need for mounting your rifle. This rail system is commonly used for mounting Arca Swiss style tri-pods but it also can be used with Arca Swiss style bi-pods too, making...

The ARCA rail was designed to give you the flexibility and ease of use that you need for mounting your rifle. This rail system is commonly used for mounting Arca Swiss style tri-pods but it also can be used with Arca Swiss style bi-pods too, making...

The ARCA Rail was designed to give you the flexibility and ease of use that you need for mounting your rifle. Mount your Arca Swiss tri-pod or bi-pod, picatinny rail accessories, and a Harris bi-pod all on one mount! The ARCA 3-Way Rail beautifully...

Odin Works Arca Bag Plate, Matte Finish, Black Acc-arca-plateModel: Arca Bag PlateFinish/Color: MatteDescription: Arca Rail

Designed for use with all M-LOK mounting surfaces, the M-LOK Aluminum Cantilever Rail/Light 3-Slot Mount allows the attachment of various MIL-STD-1913 Picatinny spec rail-mounted accessories such as lights and optics, and directly interfaces with the...

The Rail Light Mount fits on any standard 1913 Picatinny Rail, is available in Right or Left side models, and integrates with the Magpul XTM panels. It positions the weapon light high and cantilevered forward, at the 11 oclock or 1 oclock position, to...

The Rail Light Mount fits on any standard 1913 Picatinny Rail, is available in Right or Left side models, and integrates with the Magpul XTM panels. It positions the weapon light high and cantilevered forward, at the 11 oclock or 1 oclock position, to...

The Magpul WCK (Wire Control Kit) provides a fast, secure, and clean way to manage light and laser wires to create a more streamlined forend on your rifle. The WCK ships with six easy-to-install M-LOK-compatible assemblies. Each assembly is a half-slot...

The Magpul WCK (Wire Control Kit) provides a fast, secure, and clean way to manage light and laser wires to create a more streamlined forend on your rifle. The WCK ships with six easy-to-install M-LOK-compatible assemblies. Each assembly is a half-slot...

Meeting the urgent requirement for an easy way to mount weapon lights and other accessories on the Benelli M4 semi-automatic shotgun, the new Truckee replacement forend provides industry standard M-LOK mounting points on both sides and the bottom...

The customized LimbSavers Classic Precision-Fit Recoil Pad is designed to specifically fit a variety of rifles, shotguns, and muzzleloaders, reducing felt recoil by up to 70 percent. The recoil pad enables you to shoot longer without discomfort and...

The customized LimbSavers Classic Precision-Fit Recoil Pad is designed to specifically fit a variety of rifles, shotguns, and muzzleloaders, reducing felt recoil by up to 70 percent. The recoil pad enables you to shoot longer without discomfort and...

The customized LimbSavers Classic Precision-Fit Recoil Pad is designed to specifically fit a variety of rifles, shotguns, and muzzleloaders, reducing felt recoil by up to 70 percent. The recoil pad enables you to shoot longer without discomfort and...

The Limb Saver AR-15/M4 Snap-On Recoil Pad securely snaps onto most six-position adjustable stocks to reduce felt recoil by up to 60 percent while reducing muzzle jump. The recoil pad helps increase the accuracy of follow-up shots and youll enjoy...

Precision fit for standard frame GLOCK 26" 27 models. THIS GRIP WILL ALSO FIT AND FUNCTION WELL ON THE FOLLOWING FIREARMS, THOUGH NOT SPECIFICALLY DESIGNED FOR A PRECISION FIT: GLOCK 26: Gen 5 (frame does not have finger grooves), GLOCK 30" 31" 32" 33"...

Featuring gentle palm swells, naturally positioned finger grooves and Hogues famous Cobblestone texture, Hogue HandALL grip sleeves provide unparalleled comfort and increased recoil absorption. Hogue HandALL grip sleeves have been engineered for a...

Precision fit for the following standard frame GLOCK Generations 1" 2 & 5 (9MM" 357 SIG, 40 S&W, 45 GAP): G19" G23" G32" G38Features :Gentle palm swells fit comfortably in handFinger grooves naturally position fingers for optimal gripTextured with Hogues...

Precision fit for the following standard frame GLOCK Generations 3 & 4 (9MM" 357 SIG, 40 S&W, 45 GAP): G19" G23" G32" G38Features :Gentle palm swells fit comfortably in handFinger grooves naturally position fingers for optimal gripTextured with Hogues...